Jerrawa Antenna Lab

Jerrawa Antenna Lab TESTING

Wire antennas, modelled for your space and your bands.

Quiet right now: a new job starts straight away.

5,245jobs finished so far
41antenna types to start from
2simulation servers online
nonewait for a new job
More about what the servers are doing

0 job(s) running, 0 waiting, and 1 background job(s). When nobody's job is waiting, the servers work through a library of antennas in the background, so answers for common situations are ready sooner. Your job always goes first: the background work pauses for it.

Updates every 15 seconds.

New: what can I put up here? no sign-up

Describe the space you have (two trees, the house and a fence post, one pole, or a few supports for a loop). The Lab tries every antenna that suits it on 80 m to 6 m, with and without a tuner, ranks what works and gives you a build sheet for each. It takes a few hours; it can email you when it's done.

I know what I want to build

Pick from 41 antenna types (dipoles, OCFs, end-feds, verticals, loops, wire beams) or paste your own NEC model. Tick what may change and choose your bands.

Help me choose

Tell it your lowest band, the gap between your supports and your tallest support, and it sizes the antenna to fit.

Just having a look

See a real result: a 150 ft delta loop worked through from the model to the balun to wind. Anyone can open it.

How it works

Describe

The antenna, your space and your bands.

More

Pick from 41 antenna types or paste your own NEC model. Not sure of the sizes? Start from what you have sizes it from your lowest band, the gap between your supports and your tallest support.

Model

NEC-2 tries hundreds of versions over real ground.

More

Every band is checked edge to edge, and the balun ratio is worked out for you. It also shows what moves each band, and which other band sets the same wire can do.

Build

Lengths to cut and the balun to wind.

More

Measurements in metres and %, how carefully to cut each one, and a check that adds random build errors to see if it still works. The balun turn by turn, with a test resistor. A build sheet to print.

Check

Where your signal goes, and whether your tuner can match it.

More

Each band against a plain dipole at the same height. Your tuner checked with its real coil and capacitors. A table for your analyser readings, and a link to share with a mate.

What a result looks like

A real job: a 150 ft (45.7 m) delta loop, bottom wire 3 m up, over poor ground, with a remote tuner at the feed.

7 of 10 bands40, 20, 17, 15, 12, 10 and 6 m. The tuner check says this tuner can match 30 m as well.
One length to watchEach side has some room: 46 cm short loses 40 m, 46 cm long is fine.
The balun to wind21 turns tapped at 8 on an FT-140-43, plus a choke.
Top view (from above) X axis → (the bearing you set in the radiation report) Side view (heights) ground feed 15.24 m 15.24 m 7.62 m 7.62 m Highest point 16.20 m up, lowest 3.00 m 2 m 10 m Space it covers from above: 15.2 m long

Drawn to scale from this design's NEC model (each view has its own scale bar). Lengths are along each straight wire; the red dot is the feed point. The legs either side of the feed are measured from the middle of the feed point.

Show the full summary and the SWR charts

At a glance

Bands7 of 10: 40, 20, 17, 15, 12, 10, 6 m. Not: 160, 80, 30 m.
Your ATU-100 7x7 (N7DDC design) can match 8: 40, 30, 20, 17, 15, 12, 10, 6 m. Not 160, 80 m. (30 m too: this check uses the tuner's real coil and capacitors, not the 10:1 rule of thumb.)
Radiated
?How much of your power leaves as radio waves. The rest warms the ground, the wire, coils or resistors.
40 m 40% 20 m 45% 17 m 66% 15 m 61% 12 m 67% 10 m 62% 6 m 63%
More than half your power gets out on 17, 15, 12, 10, 6 m; a fair share (20–50%) on 40, 20 m. The rest heats the ground, wire or coils.
Against a dipole
?Signal at low angles (good for long distance) compared with a plain half-wave dipole at the same height. Minus means weaker.
40 m −4.7 20 m −9.1 17 m −3.6 15 m −8.1 12 m −5.1 10 m −2.7 6 m −1.9
dB at low (DX) angles, 6–24°, against a plain half-wave dipole at 16.2 m over the same ground: below it on every band shown.
Building itMost careful with side length: Some room (46 cm shorter loses 40m; 46 cm longer is fine).
Feeding it
?The balun is a small transformer at the feedpoint that matches the antenna to your coax. The Lab works out the ratio and how to wind it.
A 6.89:1 balun: 21 turns tapped at 8 on an FT-140-43, plus a choke. Anything from 6.48:1 to 56.05:1 works just as well.
With your tuner at the antenna (remote), matching up to 10:1.

20 m ✓

15101514.00014.350 MHz14.000 MHz: SWR 3.03 (384+j161 Ω)14.044 MHz: SWR 2.97 (394+j177 Ω)14.088 MHz: SWR 2.90 (405+j193 Ω)14.131 MHz: SWR 2.84 (416+j210 Ω)14.175 MHz: SWR 2.78 (427+j226 Ω)14.219 MHz: SWR 2.73 (439+j242 Ω)14.263 MHz: SWR 2.67 (452+j258 Ω)14.306 MHz: SWR 2.62 (465+j274 Ω)14.350 MHz: SWR 2.56 (478+j290 Ω)

30 m ✗

15101510.10010.150 MHz10.100 MHz: SWR 12.77 (13907+j2902 Ω)10.106 MHz: SWR 12.81 (14191+j2294 Ω)10.113 MHz: SWR 12.85 (14420+j1660 Ω)10.119 MHz: SWR 12.89 (14593+j984 Ω)10.125 MHz: SWR 12.93 (14700+j297 Ω)10.131 MHz: SWR 12.98 (14742−j414 Ω)10.138 MHz: SWR 13.02 (14715−j1117 Ω)10.144 MHz: SWR 13.06 (14618−j1824 Ω)10.150 MHz: SWR 13.10 (14458−j2504 Ω)

SWR across the whole band, for every band you tick. The dashed line is the limit (here the tuner's 10:1): 20 m passes, 30 m does not by the model, though the tuner check says this tuner can still match it. Fails are part of the answer, not hidden.

See the whole result How to read a result

About the Lab

Why I built it

It started with an antenna I am building, the "May cage": a caged inverted-V with separate wires for 80, 40, 30, 20 and 10 m on one feed. Getting five bands to play together meant changing one wire, re-running the model, then finding another band had moved. Over and over. I wanted something to do that grind for me: try hundreds of combinations, show me which one works, and tell me what moves what.

In the model it found a design with all five bands under the SWR target on a 2.25:1 balun. Now it is being built for real, with 3D-printed parts where needed, and will go up on one of the towers here to see how close the model gets. The Lab grew from there.

Peter, VK2ADG

How it works, honestly
  • The numbers come from NEC-2. Every design is simulated many times with the Numerical Electromagnetics Code on servers in Jerrawa, NSW, searching for the dimensions that work on your bands.
  • No AI is needed. The search, the SWR, the balun, the build sheet and the radiation report are all plain code and NEC-2.
  • It is a guide, not a guarantee. Real ground, trees, buildings and how you build it all change the result. Cut long, then trim with an analyser.
Claude, the optional AI helper

On top of the Lab there is an optional helper, Claude (an AI made by Anthropic). It can explain a finished job in plain words, suggest the next run, fill in the form from a description, suggest antennas for your block and run small experiments for a site. For testers it is switched off by default, because every request costs the Lab money and because an AI can be wrong. Peter can switch it on for you: ask in the suggestions box.

  • Analyse a finished job. Claude reads the whole run and explains how good each band is, which lengths drive which band, what is holding back a band that fails, which balun suits, and anything that looks odd.
  • Suggest the next run. One or two ready-made changes ("Careful" and "Explore"). Tick the ones you want and the form opens with them filled in. Nothing runs until you press Queue.
  • Describe it in words. Type or paste what you have in mind, even a forum post, and Claude fills in the form with the nearest antenna type. Anything it guessed is highlighted.
  • Plan a site. Describe your block, your supports and who you want to reach; Claude suggests antennas that might fit and can run small rounds of jobs to compare them.

Claude only reads what the Lab sends it. The numbers always come from NEC-2, never from the AI, and everything Claude writes is marked as an AI reading. Testers get 3 free Claude requests to try it when it is switched on, and can buy credit for more (what Claude costs the Lab plus a small margin that pays for new testers' free tries).

Without it you can still have a chat with Claude yourself: Download for analysis on any job page gives one file with the whole run and a ready-made prompt to attach in your own chat.

"Can't MMANA, 4nec2 or EZNEC already do this?"

Yes, and they are excellent; most of us learned on them. The Lab is for a different way of working:

  • Easy to drive. Describe the antenna, tick what may change, choose your bands, and walk away. No steering an optimiser, no editing wire tables.
  • Many bands at once. Every band is checked across its whole width on every design, and the balun ratio is worked out for you.
  • Real ground. It uses NEC-2 with real ground, which matters for low wires, verticals with radials and NVIS antennas. MMANA's MININEC engine treats the ground as perfect when it works out the impedance.
  • Answers you would otherwise work out by hand: what moves each band, how fussy each dimension is, and where your signal goes from your own location.
  • It works alongside them. Every design downloads as a NEC file to open in 4nec2 or EZNEC, to check it or carry on.
Who is behind it

The Lab is a hobby project by Peter May, VK2ADG, at Jerrawa in the Southern Tablelands of NSW. It is not a business and is not trying to make money. It does cost money to run (servers, cloud time when it is busy, and the AI), so if it ever asks for a contribution, that is only to cover those costs. It is still being built: more is coming, and what gets built next depends a lot on what people ask for below.

Credits: the simulations use NEC-2, written by Gerald J. Burke and Andrew J. Poggio at Lawrence Livermore National Laboratory, through nec2c, the C translation by Neoklis Kyriazis, 5B4AZ. Any mistakes in how the Lab uses NEC are ours, not NEC's.

Test version: please read before you use the results

Please read: test version, use at your own risk

  • These are computer models, not guarantees. Results come from NEC2 simulations of an idealised antenna. Real ground, trees, buildings, masts, feedlines and how the antenna is built will change the results. Treat every number as a starting point: cut long, then trim with an antenna analyser.
  • Not engineering or safety advice. Nothing here tells you an antenna is safe to put up. You are responsible for your installation: keep well clear of power lines, use sound supports and fixings, and provide proper lightning and earthing protection.
  • Licence and RF exposure are your responsibility. Operate within your licence conditions and the ACMA (or your own regulator's) RF exposure (EME) requirements.
  • No promises about the service. This is a hobby project in testing. It may be slow, stopped, reset or withdrawn at any time, and jobs and results may be deleted without notice.
  • Keep it non-personal. Don't put private information in job names or models. Anyone with a job's link can see that job.

By queuing a job you accept these terms and use the results entirely at your own risk.

Joining the trial

Testing is open to a small group at a time (7 testing now, 0 waiting). Join the list and you will be emailed when a place is free. Log in is by an emailed link: no passwords. If you have a job link, it opens directly. Testers with a code can still use it on the job form.

Join the trial Log in

Make a suggestion

Ideas, an antenna you would like added, or something that is not working. We will see what we can do.

Your details are only used to reply to you, and are deleted on request. We count visits with jerrawa.org's own simple counter (which pages, how long, which link brought you here); there are no Google or Facebook trackers.