One real result, section by section: what each part shows, what it says about this antenna, and why. The example is a 150 ft (45.7 m) delta loop with its bottom wire 3 m up, over poor ground, with a remote tuner at the feed.
Open the example resultHave it open beside this page. Numbers below are from that page on 26 Oct 2026.
Every result starts with five lines. Each one is the short version of a section further down, so read it first, then go to the section that matters to you.
At a glance
Bands
7 of 10: 40, 20, 17, 15, 12, 10, 6 m. Not: 160, 80, 30 m. Your ATU-100 7x7 (N7DDC design) can match 8: 40, 30, 20, 17, 15, 12, 10, 6 m. Not 160, 80 m.(30 m too: this check uses the tuner's real coil and capacitors, not the 10:1 rule of thumb.)
Radiated
40 m40%20 m45%17 m66%15 m61%12 m67%10 m62%6 m63% More than half your power gets out on 17, 15, 12, 10, 6 m; a fair share (20–50%) on 40, 20 m. The rest heats the ground, wire or coils.
Against a dipole
40 m−4.720 m−9.117 m−3.615 m−8.112 m−5.110 m−2.76 m−1.9 dB at low (DX) angles, 6–24°, against a plain half-wave dipole at 16.2 m over the same ground: below it on every band shown.
Building it
Most careful with side length: Some room(46 cm shorter loses 40m; 46 cm longer is fine).
Feeding it
A 6.89:1 balun: 21 turns tapped at 8 on an FT-140-43, plus a choke. Anything from 6.48:1 to 56.05:1 works just as well. With your tuner at the antenna (remote), matching up to 10:1.
Why it is thereA results page has a lot on it. These five lines answer the questions most people ask first: does it work on my bands, does the power actually get out, is it any good for DX, can I build it, and what do I feed it with.
2. Bands: what "works" means
A band works when the SWR is at or below your limit across at least 80% of the band, through the balun shown. The Lab checks several points across every band, edge to edge, not just the middle. Your limit is the SWR you set, or your tuner's range if you have one (here 10:1, for a tuner at the antenna).
20 m ✓
30 m ✗
Each dot is one point the Lab simulated. The dashed line is the limit.
In the example7 of 10 bands work: 40, 20, 17, 15, 12, 10 and 6 m. 160, 80 and 30 m do not. 40 m only just makes it (SWR 9.4 to 10 against a 10:1 limit).
WhyA loop works best near the frequency where the wire round it is one wavelength. 45.7 m is one wavelength at about 6.6 MHz, so 40 m is close (the feed is about 115 to 125 ohm there). On 80 m the loop is only half a wavelength round, and a half-wave loop has a very high feed impedance with a lot of reactance (thousands of ohms). On 30 m it is about one and a half wavelengths, which is also very high. The upper bands are harmonics, where the impedance comes back into a range a balun and tuner can handle.
Fails are part of the answer. A band that nearly passes tells you something too: see What moves each band.
3. Radiated: how much really gets out
Radiated is the share of your power that leaves the antenna as a signal. The rest heats the ground under it, the wire, coils or resistors. It comes from the radiation report, with the ground losses taken off. Over 50% is good. Under 20% means the band only works on paper.
Band
40 m
20 m
17 m
15 m
12 m
10 m
6 m
Radiated
40%
45%
66%
61%
67%
62%
63%
In the exampleOver 60% on 17 to 6 m, but only 40 to 45% on 40 and 20 m. On 80 m (which does not work anyway) it is 27%, and on 160 m 18%.
WhyThe bottom wire, where the current is strongest, is only 3 m above poor ground. On the low bands 3 m is a small fraction of a wavelength, so much of the field soaks into the ground and turns to heat. Raising the bottom wire is the main fix. The higher bands see 3 m as more wavelengths up, so they lose less.
Low SWR is not the same as a good antenna. A dummy load has a perfect SWR and radiates nothing. And a low feed impedance is not the same as low efficiency either: that is set by the losses, not by the ohms at the feed.
4. Against a dipole
Gains in the radiation report are in dBi over ground: compared with an imaginary antenna that sends the same amount every way, in empty space. Over real ground they include the boost from the ground reflection (about 5 to 6 dB), so even a plain dipole shows 5 to 8 dBi. That is why the Lab also compares every design with a plain half-wave dipole at the design's top height, over the same ground, for each band. "+3 dB over a dipole" is the figure most hams mean when they say gain.
In the exampleAt low angles (6 to 24°, the angles that matter for DX), against a dipole at 16.2 m: 40 m −4.7, 20 m −9.1, 17 m −3.6, 15 m −8.1, 12 m −5.1, 10 m −2.7, 6 m −1.9 dB. Below it on every band. At its strongest angle it does better: about level with the dipole on 17 and 15 m, and 1.2 dB better on 12 m, at high angles that suit contacts a few hundred km away.
WhyOnly the apex of this loop is at 16.2 m; most of the wire is lower, and the fed bottom side is at 3 m. A dipole all the way up at 16.2 m sends more of its signal at low angles. It is a tough but honest yardstick.
Best against best. A high dipole has gaps between its lobes, so comparing at exactly the same angle can land in a gap and look far better than it is. The Lab compares the design's peak with the dipole's own peak, and its best low angle with the dipole's best low angle.
5. Can your tuner match it?
The band table uses a rule of thumb: "my tuner matches up to 10:1". The tuner check goes further. For the tuner you pick, it works out the coil and capacitor needed at every point, tries the nearest settings the tuner's relays can really make, and keeps the best. It says yes, part or no for each band, the loss in the tuner, and the relay settings (which you can download for Node-RED).
In the exampleAn ATU-100 (7 coils up to 8.5 µH, 7 capacitors up to 1,869 pF) can match 8 bands: 40, 30, 20, 17, 15, 12, 10 and 6 m. 30 m works with the real tuner even though it fails the 10:1 rule. 80 and 160 m are beyond it: it runs out of coil.
WhyA tuner can match some impedances well above 10:1 and fail on some below it: what matters is whether its coil and capacitors are big enough for that impedance at that frequency. The check is done through the balun you would actually wind (see the next section), because that changes what the tuner sees. The relay values for each tuner model are a best guess until checked against a real unit.
6. The balun
The balun (or unun) changes the antenna's impedance to suit 50 ohm coax. The Lab finds the ratio that keeps the most bands under your limit, and a window: every ratio in it works just as well. The balun guide then picks a winding inside that window that is easy to build, and shows it turn by turn with a test resistor to check it.
In the exampleThe model's best fit is 22.74:1, but anything from 6.48:1 to 56.05:1 keeps the same bands. The guide winds 6.89:1: 21 turns on an FT-140-43 with a tap at turn 8, plus a choke (14 turns of coax on an FT-240-31). Test it with a 345 ohm resistor on the antenna side; the SWR on the coax side should be under about 1.3.
WhyRatio = turns ratio squared: 21 ÷ 8 = 2.625, and 2.625 × 2.625 = 6.89. One balun on a multiband antenna is a happy medium: the impedance jumps around from band to band, so no ratio is perfect on all of them. Fewer turns are easier to wind and work better on the top bands, so the guide stays near the low end of the window. The choke keeps RF off the outside of the coax.
7. Building it: how fussy
Two things tell you how carefully to build. How carefully to cut gives, for each dimension, the range in which every working band still works (from the designs the run tried). The build check runs in the background later: it makes about 50 copies of the design, each with small random errors in every length and height, and counts how many still work on every band.
In the exampleSide length: Some room. 46 cm shorter loses 40 m; 46 cm longer is fine. The bottom height is forgiving (±9 cm or more keeps every band). The build check has not finished for this design yet.
Why40 m is the band hanging on by a thread (SWR just under 10), so it is the first to go when the loop gets smaller, which moves its resonance up and away. Cut the wire long, fold the spare back, and trim with an analyser on the day. The build check's verdict reads: Easy to build (90%+ of random builds keep every band), Build with care (70%+), Fussy (40%+), or Very fussy.
8. What moves each band
After the search, the Lab runs the best design again with each dimension a little smaller and a little larger, and shows what that does to each band. Some runs also show This wire can do…: other band sets the designs reached, and How each dimension changes the bands across its whole range.
In the example80 m (which fails) gets much better with a longer side: a bigger loop moves its resonance down towards 80 m. 17 m prefers a slightly shorter side, 15 m a slightly longer one. You cannot have both, which is the balancing act of any multiband wire.
WhyThis is where you learn cause and effect: which length sets which band, and what you would have to give up to gain a band. It is also the trim guide for the real antenna.
9. Where it sends your signal
The radiation report draws the pattern for each band from above and from the side, and gives the gain toward places around the world from your location, at the angle signals typically arrive from that far away (high angles for close-in, low for DX). You can show those as dBi over ground, or as dB against the dipole.
In the exampleOn 20 m the strongest signal goes nearly straight up (68°): good for contacts within a few hundred km, weak for DX. On 17 m the peak is at 44°, and on 10 m at 28°. Sydney (215 km, arriving at about 69°) does well on 17 to 12 m; Europe and the USA, arriving at about 13°, are weak on most bands.
WhyA horizontal antenna close to the ground sends most of its signal upward. The higher it is in wavelengths, the lower the angle of its strongest lobe. That is the same physics as the low bottom wire in section 3, seen from a different side.
10. The model and the real antenna
Everything above comes from NEC-2, a computer model. Real ground, trees, buildings, the feedline, wire insulation and how you build it all change the result a little. That is why the build sheet has a trimming table: write in what your analyser measures, next to what the model expected.
Reading the differenceEvery band's dip off by the same percentage: the wire is acting longer or shorter than the model (insulation, sag, trees); trim by that percentage. Some bands right and others off: something else changed, such as the feed position or the height. Dips in the right place but the SWR high everywhere: look at the balun (test it on its resistor) or the ground. SWR that changes when you touch the coax: RF on the outside of the coax; check the choke.
A guide, not a guarantee: cut long, then trim with an analyser.